Power Supply DC-DC Step Up 150W

-
SOLD OUT.. Akan kami update setelah restock

Harga Rp. 165.000 (cek untuk ketersediaan stock)
harga diluar ongkir

Isi Paket
1x Voltage Charger modue



Product Feature
  • SIZE: 65*47*23.5 mm
  • Module Properties: non-isolated step-up module (BOOST)
  • Input voltage :10-32V
  • Output voltage: 12-35V (adjustable)
  • Output Current: 10A (MAX)
  • Input Current: 16A (MAX) (Please enhance heat dissipation if more than 10A)
  • Output power: natural cooling 100W (MAX), enhance heat dissipation 150W (MAX)
  • Easy to drive 65W 90W dual-core notebook.
  • Use a 12V battery drive 19V 3.42A notebook, the module temperature about 45°c
  • Conversion efficiency: 94%  (measured at Input 16V, output 19V 2.5A)
  • Output Ripple: 2% (MAX) 20M-bandwidth
  • Operating Temperature: Industrial (-40°c to +85°c) (ambient temperature exceeds 40°c, lower power use, or to enhance heat dissipation)
  • Full load temperature rise: 45°c
  • No-load current: 25mA typical
  • Voltage regulation: ± 0.5%
  • Dynamic response speed: 5% 200uS
  • Short circuit protection: None (Please Install fuses and protection circuits at Input port.)
  • Input Reverse Polarity Protection: None (Please Series diode at the input port.)

Some Applications
  •  DIY an output adjustable vehicle power supply, connect the 12V input, and output could be 14-35V(adjustable freely), However, the output voltage can not be less than the input voltage.
  • Car laptop power supply: connected to 12V power supply, output voltage regulation as your notebook need.
  • Boost charger. You can use the 12V power supply to charge battery more than 12V, for example, 24V battery.

Popular posts from this blog

Paket Display LCD 16x2 Character dan 1602 IIC Converter Board

-
Image
Harga Rp. 80.000  (harga diluar ongkir) Isi Paket 1 LCD Character 16 x 2 1 1602 IIC Converter Board Silakan segera memesan paket LCD 1602 + I2C Converter Board ini di toko komponen elektronika oline kami sebelum kehabisan! Product Description LCD Character 16x2 - HD44780-Control Use the arduino library at here arduino site. LCD display module with blue backlight Wide viewing angle and high contrast Built-in industry standard HD44780 equivalent LCD controller Commonly used in: copiers, fax machines, laser printers, industrial test equipment, networking equipment such as routers and storage devices LCM type: Characters Can display 2-lines X 16-characters Operate with 5V DC Module dimension: 80mm x 36mm x 12mm Viewing area size: 64.5mm x 16mm Product Description 1602 IIC Converter Board IIC is good, always save your IOs on any of your MCU boards, now with this board, you can save 5 IOs, only need 2. This small converter board has a much more interesting pric
Read more

Arduino One Compatible PTH Kit

-
Image
Harga Rp. 140.000 (cek dahulu untuk ketersediaan stock) harga diluar ongkir Product Description This kit contains everything you need to build your very own Uno-Compatible development board! Simply follow the Assembly Guide and after some basic soldering, you’ll have made a fully-functional Arduino-compatible board (in fashionable SparkFun Red). The included ATmega328 comes pre-loaded with the Arduino “Optiboot” bootloader so you don’t have to worry about loading the firmware, simply solder it together, connect an FTDI Basic and load your favorite Arduino sketch! Note: You will need either an FTDI Basic or FTDI cable to load code. isi paket: 1 x Arduino-Compatible PTH Kit PCB 1 x ATMega328 with Optiboot bootloader 1 x MCP1700 3.3V Voltage Regulator 1 x 5mm Green LED 1 x 5mm Red LED 2 x 330Ohm Resistor 2 x 10kOhm Resistor 1 x 16MHz Crystal 2 x 22pF Ceramic Capacitors 5 x 0.1uF Ceramic Capacitors 2 x 100uF Electrolytic Capacitors 1 x LM7805 5V Regulator 1 x Dio
Read more

USBASP Programmer (Double Power 3.3V/5V)

-
Image
Harga Rp. 60.000 (harap kontak untuk cek ketersediaan produk) harga diluar ongkir Isi Paket 1 USBASP Programmer (Double Power 3.3V/5V) 1 Usb Cable (10 pins) Product Description This programmer is based on Thomas Fischl’s USBasp design and connects to your computer’s USB port. Not only is it quite compact, but the design is really elegant  The USB interface is achieved by using an atmega processor and the rest is done in firmware. For those interested, the firmware source code can be downloaded from the USBasp website. Features 3.3V/5V double voltage supports, double protection Auto speed Support latest S52, latest firmware. Supported ICs: 51 Series：AT89S51 AT89S52 AT89S53 AT89S2051A T89S4051 AVR Mega Series: ATmega8 ATmega48 ATmega88 ATmega168 ATmega328 ATmega103 ATmega128 ATmega1280 ATmega1281 ATmega16 ATmega161 ATmega162 ATmega163 ATmega164 ATmega169 ATmega2560 ATmega2561 ATmega32 ATmega324 ATmega329 ATmega3290 ATmega64 ATmega640 ATmega644 ATmega649 ATmeg
Read more