Stepper Motor Driver 3-axis ULN2003

-
Harga Rp. 70.000 / paket (3 pcs).



Product Description
  • Size: 42mmx30mm
  • Use ULN2003 driver chip, 500mA
  • A. B. C. D LED indicating the four phase stepper motor working condition.
  • White jack is the four phase stepper motor standard jack.
  • Power pins are seperated
  • We kept the rest pins of the ULN2003 chip for your further prototyping.
Connections:
  • IN1-4 to the MCU pins
  • The pins in the white jack (from left to the right) are: VCC, A, B, C, D (to the stepper motor)
  • Power pins are on the right, use jumper to choose either 5V or 12V.

Popular posts from this blog

EM4100 125Khz RFID Card Read Module

-
Image
Ready Stock 1 Unit Harga Rp.  195.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x board RFID card reader 125Khz 1x wire sensor 1x kabel jumper Male - Female (selama persediaan masih ada) Product Description RDM630 125KHz card mini-module is designed for reading code from 125KHz/ 134.2KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc. RDM630 Series non contact RFID module, use the advanced RF receiving circuit and embedded MCU design, combing with high efficient decoding algorithm, to finish the data receive of EM4100 and all the compatible cards. This is a very popular RFID card read module for arduino users, it can read 125K EM4100 series RFID card. This module is easy to use, serial port connect to arduino MCU after power up, when RFID car enter into card reading range, this...
Read more

Arduino One Compatible PTH Kit

-
Image
Harga Rp. 140.000 (cek dahulu untuk ketersediaan stock) harga diluar ongkir Product Description This kit contains everything you need to build your very own Uno-Compatible development board! Simply follow the Assembly Guide and after some basic soldering, you’ll have made a fully-functional Arduino-compatible board (in fashionable SparkFun Red). The included ATmega328 comes pre-loaded with the Arduino “Optiboot” bootloader so you don’t have to worry about loading the firmware, simply solder it together, connect an FTDI Basic and load your favorite Arduino sketch! Note: You will need either an FTDI Basic or FTDI cable to load code. isi paket: 1 x Arduino-Compatible PTH Kit PCB 1 x ATMega328 with Optiboot bootloader 1 x MCP1700 3.3V Voltage Regulator 1 x 5mm Green LED 1 x 5mm Red LED 2 x 330Ohm Resistor 2 x 10kOhm Resistor 1 x 16MHz Crystal 2 x 22pF Ceramic Capacitors 5 x 0.1uF Ceramic Capacitors 2 x 100uF Electrolytic Capacitors 1 x LM7805 5V Regulator 1 x Dio...
Read more

Flow Sensor - model SBS-HZ 21 WA

-
Image
Harga Rp. 100.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x Flow Sensor Model SBS-HZ 21 WA Product Description 100% brand new and high quality The water flow sensor is applied for water heater, and can be used as flow switch. Straight structure, nylon and glass fiber made, waterproof and explosion-proof, heat and cold resistant Portable size and light weight, easy to install With stainless steel ball inside of the impeller, wear-proof Three wire connection: Red for positive, black for negative, yellow for pulse signal Maximum water pressure: 1.75MPa Working range: 1-30L/min Size: Approx. 5.6*3.5*3.5cm (L*W*H) External diameter: 1.9cm Inner diameter: 1.1cm Cable length: 10.5cm Color: Black Note Avoid strong impact and chemical erosion; Forbid to throw or collision; Install vertically, angle of inclination should not be exceeded 5 degree Medium temperature should not be exceeded 120℃
Read more