Posts

Showing posts from 2013

EM4100 125Khz RFID Card Read Module

Image
Ready Stock 1 Unit Harga Rp.  195.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x board RFID card reader 125Khz 1x wire sensor 1x kabel jumper Male - Female (selama persediaan masih ada) Product Description RDM630 125KHz card mini-module is designed for reading code from 125KHz/ 134.2KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc. RDM630 Series non contact RFID module, use the advanced RF receiving circuit and embedded MCU design, combing with high efficient decoding algorithm, to finish the data receive of EM4100 and all the compatible cards. This is a very popular RFID card read module for arduino users, it can read 125K EM4100 series RFID card. This module is easy to use, serial port connect to arduino MCU after power up, when RFID car enter into card reading range, this mod

Water Drop - Rain Sensor - Sensor Curah Hujan

Image
Water Droplet Sensor Ready Stock : 1 Unit Harga Rp. 75.000 (kontak untuk ketersediaan Stock) harga diluar ongkos kirim Isi Paket 1x Modul Sensor + Board 1x Free Cable Product Description Voltage: 5V Have power indicator, output signal LED indicator. TTL-level output, TTL output valid signal is low, drive capacity at 100MA, can directly drive relays, buzzer, a small fan, and so on. Sensitivity adjustable via potentiometer The output is high LED light up when no rain, and vice verse. Raindrops board and the control panel is separate, convenient line leads. A large area of raindrops board, more conducive to rain detected. Board with positioning holes to facilitate installation Control panel board size: 3 * 1.6 cm The raindrop detection plate large area 5.4 * 4.0 cm Usage Connected to 5V power supply power lights, induction board no water droplets DO output is high, the switch indicator lights off, dropping on a drop of water, DO output is low, the switch i

Pl2303HX USB to COM/UART/TTL Integrated Programmer Cables

Image
Harga Rp. 70.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x  Pl2303HX USB to COM/UART/TTL Integrated Programmer Cables Product Description PL2303 USB to TTL programmer, integreated into the cable, not a board any more, easy to use and pretty well protected. Cable Length 1 meter. Same function of CP2102, FTDI 232 IC, etc, used for prgramming or updated firmware of TV box, AVR, etc. Pin Definition: Red – VCC (5V), Black – GND, Green – TXD, White – RXD. * May do not connect the Red VCC pin if you connect to other devices. Application: Simple serial communication.Router or ADSL firmware upgrade. GPS serial communication. Hard disk firmware upgrade. Easy to use, RX-MCU to the TX; TX to the MCU RX; GND connect to ground. Without the need for using a MAX232 converter. HyperTerminal; common serial debugging tools. Various satellite machine upgrade, etc. Drivers and Documentation Drivers from official web site Datasheet

Arduino Pro Micro - 5V 16MHz - ATmega32u4

Image
Harga Rp. 147.500 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket (lihat gambar) 1x Arduino Pro Micro Development Board 2x pin out Product Description The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface. This tiny little board does all of the neat-o Arduino tricks that you’re familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. This is the 5V version so, as always, keep in mind the limits of system voltage and so forth. The lower system voltage also has its advantages, though, like ease of use with many common 5V sensors. There is a voltage regulator on board so it can accept voltage up to

Arduino Pro Mini Clone Grade Ori

Image
Ready Stock 2 Unit Harga Rp. 75.000 harga diluar ongkos kirim Isi Paket (lihat gambar) 1x Arduino Pro Mini Development Board 3x pin out http://www.vcc2gnd.com/2014/01/ArduinoProMini328.html PESAN SEKARANG SEBELUM KEHABISAN! STOK TERBATAS! Overview The Arduino Pro Mini is a microcontroller board based on the ATmega168 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 8 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. A six pin header can be connected to an FTDI cable or Sparkfun breakout board to provide USB power and communication to the board. The Arduino Pro Mini is intended for semi-permanent installation in objects or exhibitions. The board comes without pre-mounted headers, allowing the use of various types of connectors or direct soldering of wires. The pin layout is compatible with the Arduino Mini. There are two version of the Pro Mini. One runs at 3.3V and 8 MHz, the other at

Relay 1 Channel 5V

Image
Harga Rp. 45.000 (kontak untuk ketersediaan stok) harga diluar ongkos kirim Isi Paket 1x Relay 1channel  Product Description The module uses the Songle relay for control, AC voltage max at 250V, AC current max at 10A, DC voltage 30V DC current maximum 10A; Basically Connecting on high TTL and open or low TTL. Operating voltage 5V  With fixed bolt hole for easy installation Small board PCB size: 7.2cm * 4.8cm Led Indicator

Flow Sensor - Model YF-S201

Image
Harga Produk Rp. 120.000 (kontak untuk cek ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x  Flow Sensor - Model YF-S201 Features This product mainly used for water testing, water cooling system the lowest rated working voltage: DC4.5 5V-24V maximum operating current: 15 mA (DC 5V) working voltage range: DC 5~18 v load capacity: ≤ 10 mA (DC 5V) use temperature: ≤ 80 ℃ operating humidity range: 35%~90%RH (no frost) allowing pressure: pressure 1.75Mpa temperature: -25~+80 ° c External threads: 1/2" High amplitude ≥ 4.6V Low amplitude ≤ 0.5V Electric strength 1250V/min Insulation resistance ≥ 100MΩ Hydrostatic pressure testing ≤ 1.75Mpa Informasi selengkapnya (dengan contoh Arduino Sketch): YF-S201 Water Flow Sensor @ Vcc2GND.com

Flow Sensor - model SBS-HZ 21 WA

Image
Harga Rp. 100.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x Flow Sensor Model SBS-HZ 21 WA Product Description 100% brand new and high quality The water flow sensor is applied for water heater, and can be used as flow switch. Straight structure, nylon and glass fiber made, waterproof and explosion-proof, heat and cold resistant Portable size and light weight, easy to install With stainless steel ball inside of the impeller, wear-proof Three wire connection: Red for positive, black for negative, yellow for pulse signal Maximum water pressure: 1.75MPa Working range: 1-30L/min Size: Approx. 5.6*3.5*3.5cm (L*W*H) External diameter: 1.9cm Inner diameter: 1.1cm Cable length: 10.5cm Color: Black Note Avoid strong impact and chemical erosion; Forbid to throw or collision; Install vertically, angle of inclination should not be exceeded 5 degree Medium temperature should not be exceeded 120℃

BMP 180 Digital Barometric Pressure Sensor Arduino Compatible

Image
Harga Rp. 70.000 harga diluar ongkos kirim Isi Paket 1x BMP180 Barometric Pressure Module FEATURES 1.8V to 3.6V supply voltage 1.62V to 3.6 I2C interface voltage 300 ... 1100hPa (+9000m ... -500m relating to sea level) Temperature measurement included Same features as it's predecessor the BMP085 Software compatible with it's predecessor the BMP085 DESCRIPTION This is a breakout board for Bosch's new barometric pressure the BMP180.  The BMP180 is the replacement for the popular BMP085 and contains all the same features while featuring a smaller package size and lower pin count.  The pressure no longer features the EOC and XCLR pins.  The best part is all registers addresses and calculations are the same as the BMP085 so the current libraries for the BMP085 will work just fine. The IO pins are not 5 volt tolerant so a level translation circuit needs to be implemented if connecting to a 5 volt microcontroller. NOTE This is the I2C version of the BMP

XL 6009 - DC-DC Stepup better than LM2577

Image
Harga Rp. 55.000 (kontak untuk ketersedian produk) harga diluar ongkos kirim Isi Paket 1x XL 6009 Our products are independent research and development and production, sophisticated technology, each products are through strict test before sent to the user. And can meet the demand of batch. 32 V - 3.2 V input output highest 38 V Output voltage range: 4 v to 38 v dc voltage continuously adjustable, high efficiency (96%) of the maximum output current for 4A. Advantage: use double thickening black oil PCB with high quality, all use imported SMD aluminum electrolytic capacitors, high Q value power inductors. And every piece of plate passes through the strict technical test, test completely using separate antistatic protection bag packaging. Note This modules relative to the LM2577 triode mode conversion efficiency is higher This module is adjustable booster module, can by adjusting the precision of modules above circle more adjustable potentiometer To change the output vo

Graphic LCD 128*64 pixels

Image
Harga Produk  240.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x Graphic LCD 128*64 pixes Product Description This is a 128×64 liquid crystal display that support Chinese character , English characters and even graphics, very suitable for interactive work with Arduino. 12864 is an unofficial Arduino library that supports 12864 Graphic LCDs that use the ST7920 chip. This module support parallel and serial interface, when using a serial port mode, DB0 – DB5 didn’t use, DB6 (SCL) : serial clock, rolled out brand-new DB7 1993 (SI) : serial model data mouth Power:VDD = + 5V or + 3V, usable software adjust contrast Display content: 128 (column) X 64 (lines) Display mode: FSTN is show a semipermeable (white background with black text) Properties: blue LED backlighting lateral backlighting, current: 80MA Control chip: ST7920, may choose to use a serial port or parallel, Set R1 0 ohms,it’s parallel port; Set R2 0 ohms, it’s serial interface. Rea

2004A LCD - 20x4 Character

Image
Harga Rp. 145.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x 2004A LCD 20 x 4 Character Feature Package:COB Mechanical maximum dimension:98 x 60 mm Connection: conducting adhesive-type Screen mension: 76 x 26 mm Connection: one single row in parallel connection Dot size: 0.55 x 0.55 mm Back-light type: EL/LED Character size: 29.5 x 47.5 mm Operational Volt: +5V/+3.3V Display color: Yellow-Green/Blue/Black & White Operation Temperature: -10 ~ +60 C Controller: SPLC780 Storage Temperature: -20 ~ +70 C Pin Definition 1 – VSS -Ground for Logic(0V) 2 -VDD -Power supply for Logic(+5V) 3 -V0 -Power supply for LCD Driver 4 -RS -H: Data;L: Instruction Code 5 -R/W -H: Read; L: Write 6 -E -Enable signal 7~14 - DB0~DB7 - Data Bus Line 15 - A Backlight Power(+5V) 16 - K Backlight Power(0V) Documentation

NRF24L01/XR - Long Range Module - Compatible Arduino

Image
Harga Rp.  260.000 harga diluar ongkos kirim Isi Paket 1 Modul  NRF24l01L/XR 1 Antena Klik pada tautan ini untuk mengecek ketersediaan stok: NRF24L01/XR Long Distance Wireless 2.4GHz Serial Communication Module Product Description NRF24l01/XR wireless module, use NRF24l01 IC from Nordic, work at 2.4Ghz worldwild open ISM band , working data speed up to 2 Mbps, 125 channel can reach multiple channel and jumping channel needs, operation voltage 3.3-3.6V, transmit power up to 20 dBm , then sensitivity can reach -86dbm at 2 Mps high speed. This module is designed for long distance as well as high speed transferring, pins and interface are fully compatible with normal NRF24L01+ module, no need extra control pins. Compact size, easy to use, simply extend the communication distance. Feature 2.4Ghz worldwide free open ISM band High working speed up to 2Mbps, high efficient GFSK modulation, can transfer audio or video. 125 channels for multiple communication or jumpi

TEC1-12706 Thermoelectric Peltier Cooler (12V, 60W)

Image
Ready Stock : 2 Units Harga Rp. 80.000 (harap kontak untuk cek ketersediaan produk) (harga diluar ongkos kirim) Isi Paket 1x TEC1-12706 Product Description Get ice cold in minutes or heat to boiling by simply reversing the polarity, used for numerous applications from CPU coolers to alternate power sources, or even for your own custom car drink warmer/cooler. Since they consit primarily of semiconductor material sandwiched between ceramic plates and have no moving parts Specification Model: TEC1-12706 Size: 40mm x 40mm x 4mm Operates from 0~15.2V DC and 0~6A Operates Temperature: -30℃ to 70℃ Max power consumption: 60 Watts These devices must be used in conjunction with a heat sink to avoid burned in 2 seconds after powered up Each device is full inspected and tested Fitted with 6-inch insulated leads The side with words are the cooling side, and other side is the warm side.

Arduino Mega 2560 R3

Image
Harga Rp. 295.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x Arduino Mega 2560 R3 + Kabel USB Product Description Arduino Mega 2560 R3 is a microcontroller board based on the ATmega 2560, fully compatible with Arduino mega 2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila. Features Microcontroller: ATmega2560 Operating Voltage: 5V Input Voltage: 7-12V Input Voltage (limits): 6-20V Digital I/O Pins: 54 Analog Input Pins: 16 DC Current per I/O Pin: 40 mA DC Current for 3.3V Pin: 50 mA Flash Mem

Saleae8 USB Logic Analyzer 24M 8-Channel

Image
Harga Rp. 220.000 (kontak dahulu untuk ketersediaan produk) harga diluar ongkos kirim Product Description A very useful debugging tool for digital signal analyzing, help you fully analyzing the UART, IIC, SPI, CAN all of these interface. If you don’t want start with expensive oscilloscope, this will be another good choice. Features A total of eight digital channels, =voltage range is 0V ~ 5.5V, the voltage threshold is considered to be low below 1.5V, 1.5V above is considered high. Package includes the main device, 10pins of dupont cable and one USB cable. See basic how it works and how to use the introduction video below. Samples : How much samples to collect, Mhz: frequency of sampling, so 50M * 1Mhz will be 50 total sampling time. This one is a starter version, different to Saleae16, which has 100Mhz, 16-channel version

Relay 8 Channel

Image
Harga Rp. 195.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x 8 Channel Relay Module Product Description The module uses the Songle relay for control, AC voltage max at 250V, AC current max at 10A, DC voltage 30V DC current maximum 10A; Basically Connecting on high TTL and open or low TTL. 9013 transistor to drive (for 4 channels), 8550 transistor (for 8 channels and 2 channels) to drive Operating voltage 5V With fixed bolt hole for easy installation Small board PCB size: 7.2cm * 4.8cm Power indicator (green), four relay status indicator (red) Connection VCC connect to 5V GND connect to GND 1N1-1N8 relay control interface connected MCU’s IO port Extra Chinese Characters explanation 常开: Always Open 常闭: Always Close 公共: Communal Documentation Get the schematic here . Silakan pesan relay 8 channel ini secara online di toko komponen elektronika online kami.

NRF24L01 Arduino Support

Image
Harga Rp. 60.000 (kontak dahulu untuk ketersediaan product) harga diluar ongkos kirim Isi Paket 1x NRF24L01 Arduino Support (Produk sesuai gambar) Product Description Overview: RF24L01B low power wireless module, use  NRF24L01 chip from Nordic, 2.4G lisence-free ISM band, highest working data speed is 2Mbps, 125channels can reach different point or jump frequency communication needs, small size 18*37 mm, high efficiency GFSK modulation, anti-interfere, specially suit for indutrial control. Features : 2.4Ghz  lisence-free ISM band Highest data speed 2Mbps,high efficient GFSK modulation, anti-interfere, specially suit for indutrial control 125 channel, can reach different point or jump frequency communication needs Integrated hardware 8/16 bytes CRC confirmation and point to mutiple points communication adress control, combine TDMA – CMDA – FDMA working principle, enable wireless communication. Low power comunpiton 1.9 – 3.6V ,Standby mode only need 1uA ; Module ca

QFP 32-48 0.8mm / TSOP 28-48 0.5mm to DIP Board Adapter - Gold Plated

Harga Rp. 27.500 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1 (satu) QFP 32-48 0.8mm / TSOP 28-48 0.5mm to DIP Board Adapter Product Description Double side, FR4 Material Special designed fit both QFP and SSOP chips Side 1: fit QFP-32/44/48 pins chip which 0.8mm pitch Side 2: fit TSOP-28-48 pins chip which 0.5mm pitch (most flash memory) Convert to DIP28-48 (2.54mm or 100mil) Thickness: 1.2mm

SOP 0.8mm / SOIC 16 pin 1.27mm Board Adapter - Gold Plated

Harga Rp. 20.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1 (satu) SOP 0.8mm / SOIC16 1.27mm Board Adapter Product Description Double side, FR4 Material, 1.6mm thickness, GOLD PLATED Special designed fit both SOIC SOP SO and SSOP chips BOTTOM side: fit SSOP/TSOP 14/16 chip which 0.8mm(~31mil) pitch, body width:3.1mm(120mil) to 8.1mm(320mil) TOP side: fit SO/SOP/SOIC 14/16 chip which 1.27mm(50mil) pitch, body width:1.5mm(60mil) to 9.1mm(360mil) Convert to DIP14/16 0.6"(600mil) row spacing Thickness: 1.6mm

SOP/SOIC/TSOP 20 pin 1.27mm / 0.65mm Board Adapter - Gold Plated

Harga Rp. 22.500 (kontak untuk ketersediaan product) harga diluar ongkos kirim Isi Paket 1 (satu) SOIC 1.27mm / TSOP 0.65mm Board Adapter Product Description Double side, FR4 Material, 1.6mm thickness, GOLD PLATED Special designed fit both SOIC SOP SO and SSOP chips TOP side: fit SSOP/TSOP 14/16/20 chip which 0.65mm(~25mil) pitch, body width:3.1mm(120mil) to 8.1mm(320mil) BOTTOM side: fit SO/SOP/SOIC 14/16/20 chip which 1.27mm(50mil) pitch, body width:4.6mm(180mil) to 8.8mm(340mil) Convert to DIP14/16/20 0.6"(600mil) row spacing Thickness: 1.6mm

SOP QFP Pitch 0.65mm/0.8mm 16 Pin SMD to DIP Adapter - Gold Plated

Harga Rp. 20.000 harga diluar ongkir Isi Paket 2x SOP QFP Pitch 0.65mm/0.8mm 16 Pin SMD to DIP Adapter - Gold Plated Product Description Double side, FR4 Material, 1.6mm thickness, GOLD PLATED BOTTOM side: fit SOP 14/16 pin chip with 0.65mm(25mil) pitch, body width:3.1mm(120mil) to 8.1mm(320mil) TOP side:QFP 16 pin chip with 0.8mm(31mil) pitch Convert to DIP14/16 0.6"(600mil) row spacing

L298N Dual H Bridge DC Stepper Motor Drive Controller Board Module

Harga Rp. 77.500 harga diluar ongkos kirim Untuk pemesanan / informasi selengkapnya, klik: L298N Dual H-Bridge Motor Drive Module Product Description Good chip: L298N as main chip, ST corporation production.low heat,outstanding anti-interference performance.high working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w. can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply. Large capacity filter capacitance,afterflow protection diode, more stable and reliable. Fitur Double H bridge drive Chip: L298N Logical voltage: 5V Drive voltage: 5V-35V Logical current: 0mA-36mA Drive current: 2A(MAX single bridge) Storage temperature: -20 to +135 Max power: 25W

PT100 Sensor Suhu Waterproof

Image
Harga Rp. 60.000 (kontak untuk ketersediaan product) Harga diluar ongkos kirim Isi Paket 1x  PT100 Platinum Resister Temperature Sensor Temp Probe Waterproof Deskripsi Produk Temperature range: -20-400℃ Sensor Diameter:  Ø4 X 30 Cable Length: 0.5m External Shielding: Insulated Shielding Internal Insulation:Fiberglass

Arduino UNO R3 Clone Grade ORI

Image
Ready Stock 7 Units Harga Rp. 225.000 ( kontak terlebih dahulu untuk cek ketersediaan product ) (harga diluar ongkir) Isi Paket 1 Arduino UNO R3 + Kabel USB Product Description In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. The Uno R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The Uno R3 works with all existing shields but can adapt to new shields which use these additional pins. Arduino is an o

IC 74HC595

Image
Harga Rp. 20.000 (kontak untuk ketersediaan produk) * harga diluar ongkos kirim Isi Paket:  4 (empat) buah IC 74HC595 Shift Register Keterangan selengkapnya / pemesanan, kunjungi: http://www.vcc2gnd.com/2014/01/74HC595-Shift-Register.html The 74HC595 devices contain an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. The storage register has parallel 3-state outputs. Separate clocks are provided for both the shift and storage register. The shift register has a direct overriding clear ( SRCLR ) input, serial ( SER ) input, and serial outputs for cascading. When the output-enable ( OE ) input is high, the outputs are in the high-impedance state.

AZTechStepDown001- DC-DC Step-Down Adjustable Power Converter Module

Image
Harga 75.000 (kontak untuk ketersediaan produk) *harga diluar ongkos kirim Isi Paket 1x AZTechStepDown001 (penamaan produk hanya untuk memudahkan pemesanan saja) Product Description DC-DC Step-Down Adjustable Power Converter Module (Better than LM2596) Features 5-24V input voltage range Output voltage range: 0.93 V-18V (antihypertensive work mode, enter at least greater than the output 2V or more) Output Current: continuous 2.5A,  peak output 4A! Switch: with Soft-off feature! Shutdown current as low microampere level! Size: 45mm * 32mm * 16mm The ultra-high reliability of the inputs and outputs are ussolid capacitors! Technical Description Using synchronous rectification technology! The highest efficiency up to 98%! Note: the new version upgrades reverse polarity protection, maximum efficiency can only reach about 95%, the highest efficiency of up to about 98% of the shorted protection diode. Efficiency measured: 12V to 5V and 18V to 12V, see the attached

LED SMD 3528 White Super Bright

Image
Harga Rp. 12.000 * harga diluar ongkos kirim Klik pada tautan berikut ini untuk memesan LED SMD ini dalam paket berisi 20 pcs Super Bright White LED SMD 3528 di toko komponen elektronika online Indonesia. Isi paket 20x LED SMD 3528 White Super Bright Product Description With CE and RoHS Wavelength: 6000-7000 (nm) Forward Voltage: 3.2-3.4 (V) Forward Current: 20mA Luminous: 2000-2500 (mcd) View Angle: 120-125 (degrees)

IC PT2262 Encode Decode

Image
Harga Rp. 40.000 (kontak untuk ketersediaan produk) * harga diluar ongkos kirim Isi Paket 1 pair IC PT2262 Encode Decode Product Description PT2262 is a remote control encoder paired with PT2272 utilizing CMOS Technology. It encodes data and address pins into a serial coded waveform suitable for RF or IR modulation. PT2262 has a maximum of 12 bits of tri-state address pins providing up to 531,441 address codes; thereby, drastically reducing any code collision and unauthorized code scanning possibilities. Feature CMOS Technology Low Power Consumption Very High Noise Immunity Up to 12 Tri-State Code Address Pins Up to 6 Data Pins Wide Range of Operating Voltage: Vcc = 4 ~ 15 Volts Single Resistor Oscillator Latch or Momentary Output Type Available in DIP and SO Package Applications Car Security System Garage Door Controller Remote Control Fan Home Security/Automation System Remote Control Toys Remote Control for Industrial Use Documentation Schematic

Logic Level Converter 3.3-5V

Image
Harga Rp. 50.000 (kontak untuk ketersedian produk) harga diluar ongkos kirim Isi Paket 1 Logic level converter 3.3/5 V (PERHATIAN, rentan listrik statis, handle with care) Product Description If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. This logic level converter is a small device that safely steps down 5V signals to 3.3V and steps up 3.3V to 5V. This level converter also works with 2.8V and 1.8V devices. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side. Two inputs and two outputs are provided for each side. Bread board friendly! Can be used with normal serial, I2C, SPI, and any other digital signal. Does not work with an analog signal. The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the ‘HV’ pin, low voltage (2.8V for

Module Remote 2262 & 2272 Wireless Kits

Image
Harga  Rp. 85.000 (cek untuk ketersediaan produk) *harga diluar ongkos kirim Isi Paket 1x Remote 4 Button 1x module remote Product Description Specification Voltage(V):DC5V Static State Current (mA):4.5mA Modulation:amplitude modulation(OOK) Working temperature: -10℃~+70℃ Sensitivity(dBm):-105DB Working frequency (MHz):315、433.92MHz(266-433MHZ band free to use)(315 or 433 frequency depends on our factory manufacturing batch, this is not able to be chosen) Code methods:bonding pad code(fixed code) Dimension(LWH) of receive board:41*23*7mm Working princple(this is M4 push-down) M4(push-down: hold for output, unhold to stop output) L4(interlock:only one of four of the output can work in the same time) T4(selflock: four output are independent, push once to output and push again to stop) Features This module use LC circuit design, include amplification and rectification, output data signal is decode high TTL signal which is convient to use, cheap and use

High Power LED White 100W

Image
Harga Rp. 240.000 (kontak untuk ketersediaan produk) *harga diluar ongkos kirim Isi Paket 1x High Power Led White 100W with metal heat sink rack Informasi selengkapnya silakan kunjungi  High Power LED 100W

Sensor Alkohol MQ-3

Image
Harga Rp. 60.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x MQ-3 Alkohol Sensor Product Description This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. Sensor provides an analog resistive output based on alcohol concentration. The drive circuit is very simple, all it needs is one resistor. A simple interface could be a 0-3.3V ADC. Features 5V DC or AC circuit Requires heater voltage Operation Temperature: -10 to 70 degrees C Heater consumption: less than 750mW   Documentation Datasheet Wiring Example Arduino Breathalyzer

Sensor Gas MQ-2

Image
Harga 50.000 (harap kontak untuk ketersediaan produk) harga diluar ongkir Isi Paket 1x sensor gas MQ-2 Product Description MQ-2  Semiconductor Sensor for Combustible Gas Sensitive material of MQ-2 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensors conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration. MQ-2 gas sensor has high sensitity to LPG, Propane and Hydrogen, also could be used to Methane and other combustible steam , it is with low cost and suitable for different application. Character High sensitivity to Combustible gas in wide range High sensitivity to LPG, Propane and Hydrogen Fast response Wide detection range Stable performance、long life、low cost     Simple drive circuit Application Domestic gas leakage detector Industrial Combustible gas detector Porta

VoltMeter 0-200 V 3 wire access

Image
Harga Rp. 55.000 (kontak untuk ketersediaan produk) *harga diluar ongkos kirim Isi Paket 1x Voltmeter 0-200V 3 wire access (tanpa kabel) Product Description Volt meter dengan range 0-200V, akses 3 kabel Feature Wide measurement range 0-200V. Mini Red LED display. Low power consumption. Refresh speed: 500ms. led colors:Red. Refresh speed: about 500ms/each time. Power supply:DC 4.5v – 28V. Working temperature: -10℃ – 65 ℃.

Voltmeter 0-99V - 3 wire

Image
Harga  Rp. 55.000 (kontak untuk ketersediaan produk) *harga diluar ongkos kirim Isi Paket 1 Voltmeter 0-99 V (3 wire) Product Description The voltmeter with 0.36 inches of digital ultra-small size tube has an area similar to a coin, using fully automated the SMD process manufacturing, process skills; voltage display accurate, better than any normal voltmeter. Power combined with measurement input, only two wires for easy connection. Wide operating voltage range (ie range), and can work in DC DC 3-99V range. Can be used for car / battery car / motorcycle can be used for a variety of voltage measurement purposes. Convenient access lines, used to monitor the battery voltage, grasp the battery state, and can also be used for other voltage measuring purposes.   Features Dimensions: 31mm * 14mm * 12mm (L * W * H) Display: three 0.36 LED digital tube Display color: red Range: DC 0-90V with 3 wire access Weight: 6 g Refresh rate: about 500m Measurement accuracy: 0.5% (+ / –

PL2303HX USB-TTL UART Programmer

Image
Harga Rp. 40.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x PL2303HX USB-TTL UART Programmer Product Description Application Simple Serial Port communication from USB to TTL for DIY purpose. For all kinds up-gradation of statelite TV Router, Hard disk, ADSL, modern firmware upgradation or crack. Cell phone, XBOX360, GPS, car repair, DVD upgradation All kinds of MCU, STC, NXP, etc Feature Use the PL2303HX high speed and stable control IC Over current protection Two LED for data transferring status 3.3V and 5V is avaiable Paralleled pins make it more convenient than vertical pins. Support Win7 Entire Board are covered and protected by the high quality and transparent heat-sensitive membrane, so the entire PCB is insulating with external environment in order to protect static. Documentation PL2303HX Datasheet

Led 3mm Super Bright Blue (12 pcs)

Image
Harga Rp. 10.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi paket 12x LED 3mm Super Bright Blue

DS18B20 Water-Proof Probe with cable

Image
Harga Rp. 60.000 (kontak untuk ketersediaan stock) harga diluar ongkir Isi Paket 1x DS18B20 Water-Proof Probe with cable Product Description Stainless steel probe header, anti-rust, sensor each pin separated with heat shrink tubing to prevent short circuit, internal sealant, waterproof! 1 meter cable length Stainless steel housing (6 * 50mm), the leads length of 100cm 3.0V ~ 5.5V power supply 9 to 12 adjustable resolution Temperature sensing range of -55 ? ~ +125 ? No external components, the unique single-bus interface Output leads: red (VCC), yellow (DATA), black (GND) Project example BILDR Website

LM2596 Stepdown DC-DC with Voltmeter

Image
Harga Rp. 95.000  harga diluar ongkos kirim Untuk memesan di toko komponen elektronika online Vcc2GND.com, silakan klik: DC-DC Buck Converter Adjustable Step-Down Voltage Regulator LM-2596 with LED Voltmeter Product Specification Module Model:LM2596 Buck Converter + Voltmeter Cutting Size: 66.04mm x 35.05mm Input Voltage: DC 4.0~40V Output Voltage: 1.25V~37V (continuously adjustable, the input voltage must be 1V higher than the output voltage) Output Current: 2A(normal and stable), 3A Max. Ripple Frequency: About 150Khz Ripple Peak: About 100mV Display Color: Red Voltage Meter Error: ± 0.1V Measure Range:4~40V (for measure accurately, please ensure that the input voltage is more than 4V) IN+: Input Postive IN-: Input Negative Out+: Output Postive Out-: Ouput Negative Features A key switch input and output voltage green light: measuring the output voltage red light: measuring the input voltage with terminal and retain the wire bonding wiring point If re

Stepup DC-DC upto 5V

Image
Harga Rp. 50.000 (kontak untuk ketersediaan produk) harga diluar ongkir Isi Paket 1x Modul Stepup DC-DC upto 5V  1x USB Connector Product Description Module Properties: non-isolated boost Rectification: non-synchronous rectification Input voltage: 2.5V-5V Output Voltage: 5.5V Output current: 1000mA (max) Conversion efficiency: 92% (maximum) Switching frequency: 1MHz Output ripple: 20mV (max) Load regulation: ± 0.5% Voltage regulation: ± 2.5% Operating temperature: -40 ℃ to +85 ℃ Output Mode: Standard USB Size: 28 x19x 8 mm ( 1 3/32 x 6/8 x 5/16 in )

ATMEGA8 DIY Minimum System Development Kit

Image
Klik gambar untuk mengecek harga jual dan ketersediaan stok ATmega8 Development Board DIY Kit di toko komponen elektronika online Vcc2GND.com

Infrared Universal PC838

Image
Harga Rp. 10.000 (kontak untuk ketersediaan produk) harga diluar ongkir Isi Paket 1x IR Receiver (PC838) 1x Led 3mm IR Transmitter Product Description Operation voltage:2.7-5.5V Receive arrange:10-15 meters 1- output, 2- GND, 3-VCC from right to left from front view side, you can connect it directly to your arduino Including EMC shielding

IC PT2272

Image
Harga Rp.  30.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x IC PT2272 Documentation PT2272 Datasheet

Breadboard Mini Transparent

Image
Harga Rp.26.000 (kontak utk ketersedian produk) harga diluar ongkos kirim Isi Paket 1x Breadboard mini transparent Product Description Size: 1.8" x 1.4" x 0.3" (47 x 35 x 8.5mm) Tiepoints: 170 Tiepoint Mechanism: Phosphor bronze nickel plated spring clips Tiepoint Pitch: 0.1" (2.54mm)

Breadboard Mini

Image
Harga Rp.25.000 (kontak utk ketersedian produk) harga diluar ongkos kirim Isi Paket 1x Breadboard mini Note: stok terbatas, bila ingin pilih warna silakan kontak terlebih dahulu Product Description Size: 1.8" x 1.4" x 0.3" (47 x 35 x 8.5mm) Tiepoints: 170 Tiepoint Mechanism: Phosphor bronze nickel plated spring clips Tiepoint Pitch: 0.1" (2.54mm)

Breadboard Lego

Image
Harga Rp. 85.000 (kontak untuk ketersediaan produk) harga diluar ongkir Isi Paket 1x board landasan 6x mini breadboard lego Saat prototyping, sering kali menghabiskan waktu mengatur layout, ditambah kabel jumper yang berantakan. Dengan breadboard logo ini, mempermudah layout, bekerja modular, dan tentunya, prototype lebih rapih dan enak dilihat. Prototyping project elektronika menjadi lebih menyenangkan.

LED 10W High Power Full White

Image
Harga Rp 40.000 (kontak untuk ketersediaan product) harga diluar ongkos kirim Isi Paket 1x LED 10W High Power Full White Product Description Chip: 30*30, Double Golden-Line Forward Voltage: (3 serial and 3 parallel) DC 9-12V (Serial connect 2 ohm resistor if you use 12V) Forward Current: (3 serial and 3 parallel) 900mA Color temperature: white :6000-7000K Bright lighting:900-1000LM (lumens) Beam Angle :120-140 Life: more than 100,000 hours Operating Temperature: -20-60 degrees Storage Temperature: -20-60 degrees

3PCs TCRT5000 – Infrared Reflective/Proximity Sensor

Image
Harga Produk Rp. 25.000  (kontak untuk cek ketersediaan produk) harga diluar ongkir Isi Paket 3x TCRT5000 Product Description The TCRT5000 have a compact construction where the emitting-light source and the detector are arranged in the same direction to sense the presence of an object by using the reflective IR-beam from the object. The operating wavelength is 950 mm. The detector consists of a phototransistor. Features Compact construction in spacing of 0.1 No setting efforts High signal outputs Low temperature coefficient Detector provided with optical filter Current Transfer Ratio (CTR) of typical 2.5%

Gear Plastik untuk Robotik

Harga Rp. - harga diluar ongkir Isi Paket 1 Pack Gear Plastik untuk Robotik DIY

TFT01 Shield for 3.2 - 4.3 inch for Arduino Mega

Image
Harga Rp. 150.000 (kontak untuk ketersediaan produk) harga diluar ongkos kirim Isi Paket 1x TFT Shield for Arduino Uno (3.2 / 4.3 inch) Product Description This board have update to Rev2.0 and white color, its cancel the 16bit mode and IRQ support. The CS connect to GND. So the code need modified, we have update to Demo code . The TFT01 LCD module is work in 3.3V voltage level and it’s not compatible with Arduino pins , so we make a shield for Arduino. Now user can directly plug the TFT01 in the shield and stand on the Arduino board. Documents Schematic v2.0 V2.0 Demo Code

ACS712 modul sensor arus

Image
Klik ACS712 Modul Sensor Arus untuk mengecek ketersediaan stok, harga murah hanya Rp75.000,-   diluar ongkos kirim Product Description The current sensor chips: ACS712ELC-20A Pin 5V power supply, on-board power indicator The module can measure the positive and negative 20 amps, corresponding to the analog output 66mV /A No test current through the output voltage is VCC / 2 PCB board size: 33 (mm) x14 (mm)